§

November 20, 2026

What to check in your fall response plan for farms, warehouses and field sites

By @everydayworkersafety

❦

Why a fall response checklist matters for remote and industrial sites

Farms, warehouses and field sites share a problem: workers often spend long periods alone or out of sight. A fall in a grain shed, a loading bay or a paddock can go unnoticed for hours unless there is a reliable way to raise the alarm. A fall detection alarm is one piece of the puzzle, but the whole response chain - from detection to help arriving - needs regular checks. This article runs through the key points to verify so that your fall response plan actually works when it is needed.

1. Confirm the alarm device is worn correctly

A fall detection alarm only works if the worker wears it as intended. On a farm, that might mean clipping it to a belt or wearing it in a chest harness under overalls. In a warehouse, the device often sits inside a hi-vis vest pocket or on a lanyard. The position matters because the sensor inside uses an accelerometer and sometimes an impact sensor to tell the difference between a real fall and a quick bend to pick up a sack. Check that the device stays in the same orientation during a normal shift. If it moves around too much, the alarm may trigger a false alarm or, worse, miss a genuine fall.

2. Test the fall detection and man down alert features

Most modern lone worker alarms include automatic fall detection and a "man down" alert that triggers if no motion is detected after a fall. The sensitivity and timing of these features vary. Some devices use a pre-alert stage: a brief warning tone or vibration that gives the worker a chance to cancel the alarm if they are fine. That pre-alert window is a good thing - it cuts down on false alarms - but it must be long enough for a worker who is winded or disoriented to respond. Test the alarm by dropping the device onto a soft surface (or performing a controlled drop with a colleague) and timing how long it takes for the alert to escalate. If the delay is too short, you get nuisance alarms. If it is too long, help may be late.

What to check in your fall response plan for farms, warehouses and field sites

3. Review the alert delay and escalation path

Once the alarm is triggered, what happens next? A fall detection alarm usually sends an alert to a monitoring service, a supervisor's phone, or a base station. The time between the device sensing a fall and someone actually receiving the alert is the alert delay. Check the device's settings for the no-motion timer and the fall-impact threshold. Also verify the escalation path: if the first responder does not acknowledge the alert, does it automatically go to a backup contact? On a remote farm, the backup might be a neighbour or a family member. In a warehouse, it could be the shift manager and then security. Write down the expected response time for each step and test it with a drill.

4. Check for false alarm triggers in the work environment

Warehouses have forklifts reversing, pallets being stacked and workers climbing ladders. Farms have uneven ground, gates to open and animals moving around. All of these actions can look like a fall to a sensitive impact sensor. A device that is too sensitive will produce frequent false alarms, which leads to alarm fatigue - people stop taking them seriously. Review the device's sensitivity settings and adjust them if needed. Some devices allow you to set a higher impact threshold for heavy work or a longer no-motion delay for tasks that involve kneeling or lying down. The goal is a balance: sensitive enough to catch a real incident, not so sensitive that it cries wolf.

5. Verify the communication and location accuracy

When a fall detection alarm is raised, the responder needs to know where the worker is. On a large farm or a multi-acre field site, GPS coordinates are essential. Check that the device's GPS fix is accurate in the places where people work - inside a metal-clad shed, near tall silos or in a concrete warehouse. A device that loses GPS signal indoors may fall back to cellular triangulation, which is less precise. Run a test by having a worker wear the device in each zone and then triggering a test alarm. Confirm that the reported location matches the actual spot. Also check that the two-way voice communication (if the device has it) works clearly enough for a responder to talk to the worker and assess their condition.

6. Train everyone on the pre-alert cancel procedure

The pre-alert stage is the worker's chance to stop an accidental alarm. But if they do not know how to cancel it, they will either ignore it (hoping it stops) or accidentally escalate it. Train each worker on the specific gesture or button press that cancels the pre-alert. Demonstrate it during the onboarding and repeat it during refresher sessions. For workers who wear gloves, check that they can still operate the cancel function without removing them. A worker who is cold, tired or in a hurry should not have to fumble with a tiny button.

What to check in your fall response plan for farms, warehouses and field sites

7. Run a scheduled incident response drill

A checklist is only as good as the practice behind it. Once a quarter, run a drill where a worker simulates a fall (for example, by lying still on the ground for the no-motion timer) and the whole response chain is activated. Time how long it takes for the alarm to reach the responder, for the responder to call the worker, and for help to arrive at the scene. Note any delays or confusion. After the drill, debrief with everyone involved and update the checklist accordingly. This is also a good time to review the settings on the lone worker alarm itself - battery level, signal strength and any changes to the work environment that might affect detection.

8. Keep the device firmware and settings up to date

Fall detection technology improves over time. Manufacturers release firmware updates that refine the fall algorithm, improve battery life or fix bugs. Check the device's current firmware version against the manufacturer's latest. If you use a platform like loneworkeralarms.co.nz to manage the devices, log in and verify that all devices are on the same version. Also review the device settings periodically. A setting that worked for a summer harvest may need adjustment for a wet winter when workers move more slowly and wear bulky clothing.

9. Document the fall response plan and post it visibly

Even the best fall detection alarm is useless if no one knows how to respond. Write a one-page plan that lists: what the alarm sounds like, who to call first, what information to give (worker name, location, nature of incident), and what to do if the first responder does not answer. Post this plan in the break room, the warehouse office and the farm shed. Include it in the induction pack for new workers. Review the plan every six months with the whole team. A plan that sits in a drawer is not a plan - it is a piece of paper.

10. Review the device's battery and charging routine

A dead battery is the most common reason a fall detection alarm fails. Check that each device is charged at the start of every shift and that the charging station is in a clean, dry place. Some devices have a low-battery warning that appears on the screen or as a flashing light. Make sure workers know to report that warning immediately, not at the end of the day. For devices that use replaceable batteries, keep a stock of spares on site and label the expiry date. A quick visual check at the start of each shift can save a lot of trouble later.

What to check in your fall response plan for farms, warehouses and field sites

Final check: the plan works in the real world

A fall detection alarm is a tool, not a solution by itself. The whole system - the device, the settings, the training, the response team and the communication path - has to work together. Use this checklist as a starting point and adapt it to your specific site. Walk the ground with the device, talk to the workers who wear it, and keep improving the plan. For more information on selecting and managing lone worker alarms, resources from loneworkeralarms.co.nz can help you match the right device to your site's conditions. A good fall response plan is a living document, not a once-a-year exercise.

❧